Medical Grade Polystyrene Or Polypropylene Test Tubes
video
Medical Grade Polystyrene Or Polypropylene Test Tubes

Medical Grade Polystyrene Or Polypropylene Test Tubes

Characteristic ● Tubes: made of medical grade polystyrene or polypropylene ● Caps: made of medical grade polyethylene ● Tubes are available in two sizes: 12 × 75mm and 13 × 100mm

Description

 

Characteristic

● Tubes: made of medical grade polystyrene or polypropylene

● Caps: made of medical grade polyethylene

● Tubes are available in two sizes: 12 × 75mm and 13 × 100mm


    Ordering Information


    Cat#

    Description

    Size(mm)

    Material

    Color

    Volume

    SterileUnitTotal

    12-1275

    Tube

    12×75

    PS

    Clear

    5ml

    No

    500 /Bag, 4 Bags/Case2000 /Case

    12-2275

    Tube

    12×75

    PP

    Clear

    5ml

    No

    500 /Bag, 4 Bags/Case2000 /Case

    12-1300

    Tube

    13×100

    PS

    Clear

    8ml

    No

    250 /Bag, 8 Bags/Case2000 /Case

    12-1299

    Cap

    12x13.5

    PE

    Blue

    -

    No

    1,000 /Bag, 2 Bags/Case2000 /Case

    12-1299

    Cap

    13x17.5

    PE

    Red

    -

    No

    1,000 /Bag, 2 Bags/Case2000 /Case


    --2-1

    --2-2

    1.What are the main factors that influence the maximum centrifugal acceleration force?

    Use of organic solutions, temperature below 0°C, centrifuging without centrifuge adapter, etc. Conduct a trial run to determine proper conditions before any critical use begins.

    The RCF (relative centrifugal force) or G ratings for our disposable centrifuge tubes have been established at room temperature using tubes filled to nominal capacity with water and centrifuging for 30 minutes. recommended carriers, adapters, and cushions that fully support the tubes. If an angle head rotor is used or proper support is not provided, G values will be lower.

    Do not confuse speed or revolutions per minute (RPM) with relative centrifugal force (RCF). Instructions for centrifuging a sample at a given RPM and time are incomplete unless the rotor or radius is specified. Protocols should always state the time and RCF value for centrifuging a sample.

     2.What are autoclaving guidelines of plastics?

    To ensure successful steam sterilization of your plastic labware please adhere to the following guidelines: PLEASE NOTE THAT NOT ALL PRODUCTS ARE AUTOCLAVABLE. Autoclave plastic consumables at 121°C and 15psi/1 atm for 15 minutes. Do not use a dry cycle, as this may cause deformation or weakening of the plastic. Allow temperature within the autoclave to return to 80°C or below before removing products.

     

    3.What are Biologix’s Commitments to Quality?

    At Biologix, we look at quality from every angle in terms of functionality, safety, purity, formulation, consistency, manufacturing, customer service, technical support, and much more, all in order to consistently ensure customer satisfaction. According to the detailed QA/QC procedures for our manufacturing facility, each and every product is traceable by lot, regardless of packaging format. Products must go through a five-step human inspection before being released for packaging. Our facility is equipped with the latest instruments and technology from the most trusted manufacturers, ensuring that Biologix applies the most stringent standards to certify that products are free from RNase, DNase, endotoxin (pyrogens), etc.



    Hot Tags: medical grade polystyrene or polypropylene test tubes manufacturers, suppliers, factory, price

    You Might Also Like

    Shopping Bags